Hopper Bin In-Boot Agitator
A Hopper Bin In-Boot Agitator is designed to both reduce feed bridging to improve flow and reduce out-of-feed events with no impacts that compromise bin integrity. The Flow-Pro System works by providing gentle agitation inside the bin’s plastic boot. It’s available for both straight and 30-degree transitions and automatically activates when feed delivery is running.…
Read MoreMarket Truck Platform Lift
Certain wheelchair lifts that are intended for use with full-size vans can work well as a Market Truck Platform Lift for loading produce (via dolly or cart) going to market. The one pictured here is a BraunAbility Millennium Series lift designed for side- or rear-door entrance into a van; in this case, it is mounted…
Read MoreHopper Bin Jitterball Agitator
The 16-inch-long Hopper Bin Jitterball Agitator is designed to reduce bridging and feed separation by utilizing the motion of the auger to agitate the bin’s contents. It reportedly installs by sliding it into the access plate.
Read MoreHopper Bin Center-Cone Agitator
A Hopper Bin Center-Cone Agitator is designed to reduce bridging by directing feed flow away from the center of the unloader boot and out toward the edges. The heavy-walled molded cone, which bolts to the hopper collar, wobbles slightly to keep the feed from only flowing down the center of the bin. The device reportedly…
Read MoreJake’s Wire-Tightener System
Jake’s Wire-Tightener System is designed to allow one to quickly tighten loose fence wire without having to cut and splice. The system simply consists of a 1/4-inch-thick, double U-shaped “clip” (about 3+ inches in length) plus a hand-held “turning tool.” One end of the tool is slipped into one U-shaped end of the clip, which…
Read MoreHand-Held Suction Lifting Tools
The DeWalt and Grabo Hand-Held Suction Lifting Tool-providing up to 265- and 375-pounds lift capacities, respectively-will reportedly work on a wide range of surfaces (non-porous, semi-porous, rough-textured). The tools’ built-in pressure sensors automatically control the battery-powered vacuum pump to produce and maintain the required degree of suction. They both reportedly create, within seconds, a secure…
Read MoreNoonee Chairless Chair Exoskeleton
The Noonee Chairless Chair Exoskeleton is designed to convert in a matter of seconds from a rigid leg-support brace for standing and walking into a chair for sitting. This allows one to temporarily rest in an ergonomically favorable position while still carrying out the task at hand. The device is worn on the back of…
Read MoreLaevo FLEX Back Exoskeleton
The customizable Laevo FLEX Back Exoskeleton is designed to reduce the risk of job-related back injuries related to a variety of actions (e.g., bending forward/backward, reaching up/out, squatting, kneeling, lifting) while minimizing physical hindrance from the exoskeleton. The main parts of the device include a vest and adjustable supports for both thighs, all of which…
Read MoreOver-the-Engine Topside Creeper
An Over-the-Engine Topside Creeper, the top portion of which adjusts up to 65 inches, fits over the engine of most autos and pickups. (For bigger trucks, it may need to be on a platform.) The steel-tube-frame device usually includes four caster wheels, wide access steps, and a cushioned chest pad. It’s load-rated up to 400…
Read MoreUnder-the-Dash Creeper
An Under-the-Dash Creeper is designed for accessing hard-to-reach areas beneath a vehicle’s dashboard (or steering wheel) while providing a relatively comfortable work position over extended periods. It consists of a cushioned lay-on board (about 40 inches long, 15-20 inches wide), at one end of which is a height-adjustable, two-legged steel frame fitted with lock-brake or…
Read MoreLadder-Mover Dolly Adapter
The Ladder-Mover Dolly Adapter is a simple plastic brace designed to turn a standard hand truck into a two-wheeled transporter of one’s ladder plus other supplies that can be laid on the ladder. Affixed to the hand-truck’s toe-plate, the device is designed to hold the ladder securely over most any terrain. It accommodates various types…
Read MoreDrill-Powered Trailer Jack Adapter
Hand-cranking the jack affixed to a livestock- or materials-hauling trailer for hitching it to the tow vehicle is a slow, tedious task-and likely daunting for those with shoulder, arm, hand, and/or back issues. One tested (and inexpensive) solution is to replace the crank handle with a cordless drill, which can speed up the task significantly.…
Read MoreConveyor-Floor Utility Trailer
These low-to-the-ground, tiltable Conveyor-Floor Utility Trailers are designed to make the loading, transporting, and unloading of all types of cargo both easy and safe. To on-load, palleted items, machines, etc., are first winched up onto the deck from the rear then conveyed forward, while loose bulk material is loader-bucket deposited from the back or sides.…
Read MoreLivestock Virtual Fencing Systems
With Livestock Virtual Fencing, a producer can keep track of animals within a given pasture area and relocate them to another part of that area or another area altogether. This allows him/her to practice rotational grazing without having to erect, constantly move, and maintain a physical fence. Most systems consist of (1) a GPS base…
Read MoreTrac-Grabber Tire Traction Aid
The Trac-Grabber Tire Traction Aid is designed to provide a simple solution to free a vehicle that’s stuck in mud, sand, snow, or adverse terrain. To get unstuck, just strap the device over the tire of each drive wheel and slowly apply power. As you do, it will lift and move the vehicle forward until…
Read MoreStrap-on Kneeler Seat
A Strap-on Kneeler Seat (equipped with high-density cushions) is designed to support one’s back, shoulders, and neck as well as relieves knee pressure when engaged in work or activity that requires prolonged kneeling. The device will reportedly bear the weight of an adult, is designed to be simple to affix the remove, allows one to…
Read MoreBobcat MaxControl Remote System
With a Bobcat MaxControl Remote System, one is able to operate/control the loader’s functions and attachments from outside the machine’s cab via iPhone or another iOS device. This means that the need to climb into the skid-steer cab is eliminated, and many tasks normally requiring two persons can now be handled solo, including backfilling, post…
Read MoreBattery-Powered Tillers/Cultivators
Tillage is digging deep into the soil to break it up, whereas cultivation is working the top portion of soil to enhance fertility and destroy weeds. The Battery-Powered Tillers/Cultivators sourced here are designed to both till and cultivate. Powered by 40- to 80-volt lithium-ion batteries and having two or three disks of steel-trowel tines, they…
Read MoreWheeled Gate with Butterfly Hinge
With this Wheeled Gate with Butterfly Hinge, the wheel allows it to roll, and the hinge allows it to pivot over uneven ground without getting stuck. The wheel, available in one size only, can be either welded or bolded onto the gate, whereas the hinge is available in various sizes depending on gate height. The…
Read MoreGPS-Tracking Ear Tag System
This GPS-Tracking Ear Tag System, which includes tags and app, allows one to remotely monitor livestock-not only as to their location, but also on their safety, health, and performance-related conditions/situations. The tags’ sensors continually monitor and (via the app) report to one’s cellular device the animal’s movement and (1) instantly send out-of-fence, illness-suspected, and calving…
Read MoreT-Post-Pulla Extraction Tool
The T-Post-Pulla Extraction Tool, which attaches to a tractor or skid-steer loader bucket, can reportedly remove over 1,000 yards of fence-line posts spaced 8 yards apart in less than an hour’s time-and without causing damage. The keys are (1) the tool’s jaws that are cut to the post’s shape, producing stronger grip and (2) the…
Read MoreProduce-Bunching Rubber Band Applicator
This Produce-Bunching Rubber Band Applicator is designed to simplify the task of packaging for market long-stem flowers and certain vegetables (e.g., asparagus. carrots, green onions). The device’s foot-controlled pedal retracts hooked arms to open the rubber band that snaps gently around the worker-held “bunch” when the pedal is released.
Read MoreTowed Bed Shaper/Mulch Layer
With this Towed Bed Shaper/Mulch Layer (Model 94), one controls both the shaping of the planting bed (either flat or crowned) and the laying of the plastic mulch that lines the shaped bed. The implement’s pre-sets allow for bed dimensions to a depth of 8 inches and a width of from 24 to 40 inches,…
Read MoreMini Tiller/Cultivator
A Mini Tiller/Cultivator is used primarily to carry out two jobs: pre-plant seedbed preparation and growing season weed removal. (It can also be used to mix compost into the soil.) As to tilling capability, this device is built more for turning over soil in an existing planting area than for breaking up new ground or…
Read MoreHomemade PTO Decoupler
Hiawatha, Kansas, farmer Jim Meuller’s Homemade PTO Decoupler has enabled for him an anything-but-easy task. His device consists simply of a U-shaped lever and a flange that he bolted (via self-locking nuts) between and a few inches down from the lever ends. The nuts hold the flange in place while allowing it to pivot. Tabs…
Read MoreDual-Wheel Tire Inflation Adapter
Affixed directly to a compressor or air hose, this 151/2 inch-long Dual Wheel Tire Inflation Adapter, which features a two-jaw chuck and remote actuator, provides the reach needed to “air up” (to a maximum 150 psi) the inner tires on grain-hauling, semis, and other large trucks. Connecting (locking on) involves pushing the chuck onto the…
Read MoreSkid-Steer Tree-Moving Attachment
This Skid-Steer Tree-Moving Attachment is designed to convert the picking up and transporting of single or multiple balled and burlapped, containerized, or boxed nursery trees from a two-/three-man task into a one-person operation. The attachment can also be used to move palleted items, boulders, or anything else that can rest on-or be squeezed by-its twin…
Read MoreFusion Drill-Powered Cultivator
Designed for already-established gardens, the Fusion Drill-Powered Cultivator can be used to mix, aerate, and weed the soil. It is well adapted to smaller raised-bed gardens because it can be shortened by removing a portion of its shaft. The 6-pound tool consists of four rotating steel tines, adjustable shaft, left- and right-side support bars at…
Read MoreLow-Tunnel Layer Machine
This tractor-towed Low-Tunnel Layer Machine (Model 95) sets the wire hoops, lays the plastic over those hoops, then disks soil over the edges of the plastic-all in a single pass. A person (seated) simply feeds the wires into the unit and monitors rollout of the plastic. Three models are available-NARROW (5-foot-wide plastic/12-inch-high tunnel); STANDARD (6-foot-wide…
Read MoreUltraLift Powered Landing Gear Tool
The UltraLift Powered Landing Gear Tool is designed to eliminate the hand-cranking typically required for raising and lowering of semi-trailer landing gear. Once one’s trailer is retrofitted with UltraLift’s bolt-on adaptor (with no permanent modifications needed to the trailer), the UltraLift is inserted into the adapter, and the trigger is used to raise or lower…
Read More